Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens Project #4

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Ariens Project #4
Original Message   Oct 15, 2011 9:35 pm
Finished redoing the dash on my blower
The new Honda 13hp engine I got to repower the blower (again)
was in great shape. Has the electric start and a 10A charging coil.
But it didn't have any of the wiring. No key switch, no rectifier, nothing.
All the factory stuff is way out of my budget so It had to go old school.
With an ignition on/off switch. (The old one that was still on the blower)
And a starter push button. Which meant that I had to rewire the whole
ignition system from the engine to the dash.
That is how things got started.
Then being the way I am, I couldn't just run new wire and leave it at that.
What's the fun it that. Anyway it's finished.
Just need to get a new impeller bearing and flanges and I can put the whole blower
back together and mate it to the tractor.


This message was modified Oct 18, 2011 by a moderator
Replies: 54 - 58 of 58Next page of topicsPreviousAllView as Outline
manjestic


Location: North Shore, MA
Joined: Oct 31, 2011
Points: 87

Re: Ariens Project #4
Reply #54   Nov 9, 2011 11:44 pm
I would say that would be acceptable, yes.  You have a push button starter switch and no key.  If you do go to a key switch with off-on-start, you might route the connection to term 2 via the "ON" part of the key switch.  My thinking is that your battery might run down when the system is off, as you are powering the regulator circuit via term 2.

You could verify this by putting an ammeter on you battery when the engine is off and see if you get parasitic draw off of the battery.
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #55   Nov 10, 2011 12:09 am
manjestic wrote:
I would say that would be acceptable, yes.  You have a push button starter switch and no key.  If you do go to a key switch with off-on-start, you might route the connection to term 2 via the "ON" part of the key switch.  My thinking is that your battery might run down when the system is off, as you are powering the regulator circuit via term 2.

You could verify this by putting an ammeter on you battery when the engine is off and see if you get parasitic draw off of the battery.

Thanks for your comment.  I will check the battery in the morning and see if it's charge has dropped from where it was this evening.
This stuff makes me crazy.  Wish I had a better understanding of it all.
manjestic


Location: North Shore, MA
Joined: Oct 31, 2011
Points: 87

Re: Ariens Project #4
Reply #56   Nov 10, 2011 7:04 am
jrtrebor wrote:
This stuff makes me crazy..


I'm in a different boat. I'm OK with the electrical. I'm uneasy about removing a cast hub frozen to the pulley and to the impeller shaft.
carlb


Joined: Nov 16, 2010
Points: 279

Re: Ariens Project #4
Reply #57   Nov 10, 2011 10:42 am
jrtrebor wrote:
Well, I hooked up term 1 to the starter solenoid.  And term 2 directly to the battery + post. 
Took reading off the battery + post
@ idle 14.6V
@ idle with the light on 13.3V
@ full throttle 14.6v
@ full throttle with the light on 14.3V
That would be a good reading.
I guess for some reason I needed to have both terminals hooked up.  Don't have any idea why that would be. 
But I believe that 14.5V @ FT is an acceptable reading. Yes?
Checked today the light is 35W

You could have hooked up both wires to either the battery or the solenoid and it wouldn't not have made any difference since the battery + post is connected directly to the + post on the solenoid. 

I agree you should be fine with the 14.5volt reading, glad to see you finally found a solution that should work fine.
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #58   Nov 10, 2011 12:15 pm
carlb - Thanks for all your input. I may go ahead and hook both wires to the solenoid.  Have any thoughts as to why I needed to have both terminals hooked up
instead of just one?  Maybe I can learn something.
This message was modified Nov 10, 2011 by jrtrebor
Replies: 54 - 58 of 58Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42