Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens Project #4

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Ariens Project #4
Original Message   Oct 15, 2011 9:35 pm
Finished redoing the dash on my blower
The new Honda 13hp engine I got to repower the blower (again)
was in great shape. Has the electric start and a 10A charging coil.
But it didn't have any of the wiring. No key switch, no rectifier, nothing.
All the factory stuff is way out of my budget so It had to go old school.
With an ignition on/off switch. (The old one that was still on the blower)
And a starter push button. Which meant that I had to rewire the whole
ignition system from the engine to the dash.
That is how things got started.
Then being the way I am, I couldn't just run new wire and leave it at that.
What's the fun it that. Anyway it's finished.
Just need to get a new impeller bearing and flanges and I can put the whole blower
back together and mate it to the tractor.


This message was modified Oct 18, 2011 by a moderator
Replies: 40 - 49 of 58Next page of topicsPreviousNextNext page of topicsAllView as Outline
carlb


Joined: Nov 16, 2010
Points: 279

Re: Ariens Project #4
Reply #40   Nov 6, 2011 5:24 pm
Well from your readings it is putting out AC and not DC.  What reading do you get when you set the meter to AC and probe both wires at the same time.  If it is actually AC output you dont want to ground either of those wires.  You would only ground the negative wire after it was rectified to DC.

At this point I would take the shroud off and see exactly where the wires are coming from and how many coils you have. 
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #41   Nov 6, 2011 9:49 pm
carlb wrote:
Well from your readings it is putting out AC and not DC.  What reading do you get when you set the meter to AC and probe both wires at the same time.  If it is actually AC output you dont want to ground either of those wires.  You would only ground the negative wire after it was rectified to DC.

At this point I would take the shroud off and see exactly where the wires are coming from and how many coils you have. 

Okay I pulled the flywheel.  I have two coils, each coil has two wires coming.  All four wires are the same color.
One wire from coil "A" is joined to one wire from coil "B"
The second wire from coil "A" is joined to the second wire from coil "B"
The two wires that have connectors on the end that I have been connecting to the rectifier. Have a wire from coil "A" and coil "B"
It is supposed to be a 10A coil system.
Flywheel has 4 magnets.
This mean anything to anyone?
While I have things apart.  Is there a way for me to check the coils with an ohmmeter to see if they are okay? If so any thoughts as what kind of readings I should get
if they are okay. And what I should see on the meter if they are bad, or partially bad or shorted.

This morning I hooked an ohmmeter between the two coil wires. That is the two wires that have connectors on the end.  Not the two that come off of each coil. "I got a tone".
I probably should have gone between a wire and ground as well.   Maybe that reading would mean something to those that know about these things
This message was modified Nov 7, 2011 by jrtrebor
manjestic


Location: North Shore, MA
Joined: Oct 31, 2011
Points: 87

Re: Ariens Project #4
Reply #42   Nov 7, 2011 3:00 pm
From your description of the splicing, the coils are in parallel.  A single phase rectifier fed by two coils to my mind implies the coils are in phase.  I'm not sure if each coil should have the same voltage output.  In parallel the voltage across them must be equal but independently, this is not true.  I'm thinking there is nothing wrong with your coils; there are two to produce more current than a single coil.  I'm a little rusty on this stuff.

Are you removing the splice?  How are you checking the coil voltages independently?

Since AC, wire color does not matter, your rect/reg will flip the negative half of the alternating current into positive.  Your voltage at the solenoid and battery will vary with RPM and battery voltage.  That is, even with a regulator, the output of the regulator will be higher when the battery is not at full capacity, than when it is at full capacity.  If your battery is significantly drained, I wouldn't necessarily be concerned about the high voltage on the output of your regulator (battery post).  I assume you are keeping a load on the output, as JimmyM says.

Paul
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #43   Nov 7, 2011 4:06 pm
manjestic wrote:
Are you removing the splice?  How are you checking the coil voltages independently?
Paul

Hi Paul
I don't know or understand much about these type of things.  I had been checking the output by taking a reading from each wire with the meter set to VAC.  Red probe to to wire
black probe to ground.  But I was assuming that each one of the two wires were connected to a single coil (that is the two wires that were being connected to the rectifier.  Which now seems not to be the case.  As you said, the coils appear to be hooked in parallel.  So I'll have to think about what that means as far as readings go.
Thanks for your input. I know very little so any information is a help.  I tend to be able to understand what things do, but have no clue how some things work.
carlb


Joined: Nov 16, 2010
Points: 279

Re: Ariens Project #4
Reply #44   Nov 7, 2011 4:50 pm
Do not check each wire to ground.  Place a probe into each of the connectors and read the AC voltage from both wires.  You only need the ground AFTER the rectifier as it is DC at that point. 

After checking the two wires in the AC mode of your tester

1 Connect both wires to the rectifier and switch your meter to DC
2 connect the output wires of the rectifier, negative to ground and positive to either the battery or the battery post on the solenoid.
3 take a voltage reading (DC) on your battery with the engine off should be 12.5 or 12.6.
6 start the engine and check the battery voltage at idle
7 bring the RPM's up to full throttle and check the volts again. 

If the battery was in the 12.5 to 12.6 range to start with I would expect to see a voltage around 13.5 or so.  If the battery was low to begin with it may take a while to bring it back up to normal voltage.

If you have a battery charger charge the battery first and make sure it is up to 12.5, 12.6 or so.
manjestic


Location: North Shore, MA
Joined: Oct 31, 2011
Points: 87

Re: Ariens Project #4
Reply #45   Nov 7, 2011 4:56 pm
jrtrebor wrote:
I had been checking the output by taking a reading from each wire with the meter set to VAC.  Red probe to to wire
black probe to ground.  But I was assuming that each one of the two wires were connected to a single coil (that is the two wires that were being connected to the rectifier.  Which now seems not to be the case.  As you said, the coils appear to be hooked in parallel.  So I'll have to think about what that means as far as readings go.

Am I correct in thinking that you were were alternately measuring each of the two wires across chassis ground.  I'd be interested in what the AC voltage across both wires (no chassis ground) is at idle and full throttle, and with and without the rectifier/regulator (and load) connected.  I hope I'm not covering ground already er...covered.

What I'm after is how the two wires (representing the two coils in parallel) are connected to the rectifier.
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #46   Nov 7, 2011 8:29 pm
manjestic wrote:
Am I correct in thinking that you were were alternately measuring each of the two wires across chassis ground.  I'd be interested in what the AC voltage across both wires (no chassis ground) is at idle and full throttle, and with and without the rectifier/regulator (and load) connected.  I hope I'm not covering ground already er...covered.

What I'm after is how the two wires (representing the two coils in parallel) are connected to the rectifier.

Thanks carlb  - This is sometimes part of my problem I don't even know how to correctly hook up and check things.  And yes I was "measuring each of the two wires across ground".  I'll have to put things back together and take a measurement across both of the wires coming from the coils.  The readings given in the photo below were taken with
the battery hooked in the system.  I hadn't checked it that day but when I checked it yesterday it was reading 12.4V.  I'll put it back in the charger and make sure it
has a full charge.
The diagrams that I have found for this rectifier. And the wiring diagram for the tractor that it came off of.  Show or call terminal #1 the Batt + terminal. The wire runs from the
rectifier to the key switch B+ terminal.  Along it's way there it is tapped into and that wire goes thru a main fuse and connects to the Battery + terminal.
Terminal # 2 is called or referred to as the Ign. terminal.  The wire goes from the rectifier to the key switch Ign. terminal.  Along its way there it is tapped into and that wire goes to a small 3 fuse, fuse block.  I hope some of this is making sense
I really appreciate all you guys help with this.  I can do a lot of things. But I can get lost when it comes to this kind of stuff.  As you can imagine with
me taking readings from the coils wires with one probe to ground.  I've simply been trying my best not to burn something up. By doing something stupid.
That I didn't know was stupid to do.  You won't be insulting me by stating simple, (doesn't everyone know this) kind of things.



This message was modified Nov 7, 2011 by jrtrebor
carlb


Joined: Nov 16, 2010
Points: 279

Re: Ariens Project #4
Reply #47   Nov 8, 2011 9:08 am
I must say i have not seen a rectifier with two hot output terminals on it, but it may be more common on tractors than snow blowers.  The light might be fine with the 17.5 volts while that would be too high for maintaining the battery. 

Maybe use term 1 @ 17 volts for the light and term 2 @ 12.5 for batt charging. 

Term one may be limited by a voltage regulator built into the rectifier
This message was modified Nov 8, 2011 by carlb
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #48   Nov 8, 2011 10:09 am
carlb wrote:
I must say i have not seen a rectifier with two hot output terminals on it, but it may be more common on tractors than snow blowers.  The light might be fine with the 17.5 volts while that would be too high for maintaining the battery. 

Maybe use term 1 @ 17 volts for the light and term 2 @ 12.5 for batt charging. 

Term one may be limited by a voltage regulator built into the rectifier

I think there a few out there, but not many snow blowers have an on board 12v electrical system.  It's almost impossible to find information and any type
of wiring diagrams for the setup I've got.  Actually I haven't found any.  That is why I've been using the Honda HT3810 tractors system as a guide for what I'm doing.
I figure that it doesn't matter whether the system is on a tractor or a snowblower.  But maybe I'm wrong about that.  All I'm hoping to accomplish is to be able to
run my light without draining the battery to the point the I can't use the electric starter to start it the next time out. 
Last year with the 11hp Honda clone and the 3A coil.
I never had a low battery problem unless I had been using the light for a while.  Usually if I did, I would throw a trickle charger on it overnight and things would be fine.
The light is only got a 25 or 35W bulb so I'm not needing that much output from the coil(s) to keep the light running and at the same time be giving the battery a little charge.
I'm going to put the flywheel back on this morning and take another reading from the coil wires.  Meter in VAC mode. With one probe to one wire and the other probe to the other wire. Then I'll make sure that the battery has a full charge. Hook it up in the system and take readings again off the starter solenoid terminal.   With the red wire on terminal #1
and then with it on terminal #2.  Would there be any reason, or would it make any sense to you.  That for some reason terminal #1 needs to be hooked directly to the battery.
And terminal #2 should be hooked to the starter solenoid?  In other words that for some reason both output terminals of the reg/rec need to be hooked to something.
Instead of the why I'm doing it which is to only have only one of the output terminals hooked to something?  I ask because the wiring diagram for the tractor shows the rec/reg hooked up that way.  In my last post I talked a little about how the tractor is wired from the rectifier.
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens Project #4
Reply #49   Nov 8, 2011 10:31 am
carlb wrote:


Maybe use term 1 @ 17 volts for the light and term 2 @ 12.5 for batt charging. 

Term one may be limited by a voltage regulator built into the rectifier

Something just occurred to me after thinking about what you said.  The rec/reg I'm using is off that Honda tractor.  It has a few other components that are putting a
draw on the system when it's running.  Like a fuel pump and a electric PTO clutch.  It also has all kinds of safety switches, buzzers, warning lights etc.
So maybe that is why the output from terminal #1 is 17v.  The rec/reg was designed for that output to handle occasional heavy loads lights, etc.
And the output from terminal #2 is a steady 12.5V for just normal load.  Not sure I put that into words to well. 
As I've said before I have to keep reminding myself that this rec/reg was not designed to be used with my engine.
The rec called for my engine is a Shindengen SH586B-12 an the one I'm using is a Shindengen SH561-12
Could be if I had the right one that the output from terminal one would be more in the 14-15V range.
Just speculating.
Replies: 40 - 49 of 58Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42