Abby's Guide to Plasma TVs
Username Password
Home Discussions Reviews More Guides

Member Profile


ccginmn

Name Chris Grenier
Email Address private
AIM
YIM
ICQ
Gender
Age
Location Saint Michael, MN
Personal Quote
Privileges Normal user
Rank
Points 5
Number of Posts 5
Number of Reviews 0
Date Joined Jan 20, 2009
Date Last Access Jan 18, 2011 2:37 pm
ccginmn's last  
Re: JD 1130SE auger belt turns over then comes off-HELP-Only about 10hours on machine
#1   Jan 18, 2011 2:28 pm
I just sent my 1130 back to Scharber & Sons with the exact same issue.  My blower was also purchased in '08 and I am lucky (or unlucky depending on how you look at it) that this happened right before my warranty ran out.  I love this blower when it is working.  Unfourtunately it has spend the majority of it's winter life at Scharber & Sons repair shop -this is the 5th time I've sent it in for repairs.  My problems to date:

1.  Primer cap fell off of the underside of gas cap and blocked the fuel line.

2.  Water got on the disk and the blower wouldn't engauge the wheels.  They fixed it with a gasket that was the 1st recall.

3.  Water got onto the disk drive again and the wheels wouldn't engauge.  They fixed it with a 2nd gasket and somekind of sheet seal under the engine (2nd recall).

4.  Gas got into the piston/carburetor and seized up the engine.

5.  Belt came off the auger assembly - I'm guessing a shaft or wheel is bent.  I'll let you know when i get it back from the shop.

That being said, my neighbor just  bought a brand new 28" Arens and only one of his wheels engauges so he had to take his back.  I'm beginning to loose faith in American products...

Re: John Deere 1130 SE
#2   Dec 28, 2009 3:34 pm
Catt wrote:
I'm happy to finally report that my 1130SE disc drive is no longer intermittently slipping and I've had plenty of snow to test it many times.  I had to seal items a little more to get it to this point.  If you can keep water off the drive disc the tires will push like crazy.



This view is inside the transmission box directly below the engine.  When snow gets on the engine it melts, runs down the sides and then underneath the engine and under the engine mounting plate.  After that it runs through the open holes and into the transmission.  I've actually caught it and know for sure these need to be sealed.  I filled most of the holes with silicone but missed two dime size holes.  I didn't think these would be a problem as they weren't open all the way through.  However, I definitely saw water and one of these is directly above the rubber disc drive wheel.  This picture shows one of the dime size holes with no silicone. The hole is covered by the engine mounting plate but it still has enough space for water to get through.







... and here it is filled with silicone (top red arrow). Make sure you fill the other dime size hole (lower red arrow) and any other open holes (yellow arrows).  One open hole is a potential problem, but as you can see there are many holes.







This is just one example of several open areas where water can get under the engine.  You can see a puddle of water to the right of the open gap.







There are many places where water can get under the engine or engine mounting plate and run into the transmission







Another large gap.








In this picture you can see silicone under the engine.  The silicone was applied from under the transmission and is coming up through the hole.








When water gets on the aluminum drive disc (yellow arrow) the rubber drive wheel slips.  Eventually the spinning aluminum disc slings the water off and the drive no longer slips.  Here you can see the water that was slung from the aluminum disc (red arrows).








I truly don't know if the next item is required, but I will explain what I did and why.
This view is of the foam fix used by Deere to supposedly correct the slipping problem.  Unfortunately in my case the foam doesn't fit very tight on the left side of the machine.  Water that gets near the foam can still run under it.







Here you can see two very small trails of water that made it's way under the foam.  The water then drops directly onto the aluminum drive pulley and gets slung potentially causing a slipping problem.







I added foam as seen below.  I extended the foam down each side to make sure water can't get on the pulley when the machine is tilted.  The side foam will be covered by the plastic belt cover.







Here is Deere's foam and the foam that I added.  It seems to be water tight.







I've had snow all over the snowblower including the engine.  Everything has been working great now.




Merry Christmas!!!


Catt,

This is the best tutorial I've seen to ensure this slipping problem is fixed.  Briggs & Stratton should be paying you to audit their engineering dept.   I'm definately going to add your suggestions to my 1130 this summer.  I just got my blower back from John Deere with both updates.  Randy at Schaber & Sons told me that B & S sent the updates out this past summer.  I personally think it should have been a recall.  Anyways, it worked great on the last snowfall so I'm happy again.  In fact, I have a new appreciation for decent equipment in general (read below).

Yesterday I tried my Dad's three-year old MTD Yardman 8hp snowblower ($800) out on 12" of snow.  Granted this isn't an apples to apples comparison as my John Deere 1130 is 10.5 hp and costs $400 more.  The MTD's wheels began slipping after about ten minutes.  It progressively got worse until it only worked about half the time.  After violently shaking it and letting it sit for 30 seconds, the wheels would engage for five more minutes before I had to repeat over and over again.  The chute had a tremendous amount of snow that came out of the backside and the adjustment is down by your knees.  Also, it only threw the snow 8 - 12 feet.  I was blowing with a good wind so this meant I started on one side of the driveway and worked my way to the other side.  Everything I threw on the first three passes landed on the other side of the driveway meaning I had to blow the same snow twice.  My little brother just purchased a 5 year-old Simplicity 924 for $600.  He also has twice the blower as compared to the MTD, although he doesn't have the bells and whistles of the 1130.  My point is that it is WAY better to buy a decent used machine than a new piece of junk. 

Re: John Deere 1130 SE
#3   Dec 15, 2009 10:43 am
I just called the local John Deere dealership (Schaber & Sons) and they are aware of the problem and will fix it under warranty for free.  The dealer was even aware of the multiple posts on this website. 

I do love this blower when it is working properly.  It's just the right size to muscle around -another 50 pounds and it would be too big.  I am actually looking forward to our next significant snowfall.  Hopefully it doesn't happen for a week or so as mine will be in for repair.  I will let you know if I run into any more problems as I am very good at belly-aching.

Re: John Deere 1130 SE
#4   Dec 15, 2009 12:28 am
I too purchased the John Deere 1130 SE and have just experienced the drive problem for the first time tonight (and second, third, and fourth times).  I was able to get mine to re engage after pulling and pushing it around a few times but definately not acceptable.  All of this after my initial fuel blockage problem. 

Last year's models came with a reservoir under the gas cap for adding fuel stabilizer.  The cap on the reservoir fell off into my gas tank and blocked the fuel line.  The manager of the lawn and garden dept at Lowes told me several people have had this problem and they would have John Deere take care of it right away.  They did free of charge and I walked away happy.  This all happened prior to "The Great Drive Problem" exlained earlier in this discussion. 

Anyways, I plan on taking my blower back to Lowes (Rogers, MN) tomorrow with this entire discussion printed out.  I see a few previous posters had to pay arond $200 to get this fixed as it wasn't covered under warranty.  That is total BS that I will not tolerate.

I wil give Lowes/John Deere a chance to fix this free of charge before I get too worked up.  I will let you know what happened later this week. 

Re: John Deere 1130 SE
#5   Jan 20, 2009 5:29 pm
Thanks Clay!!  I just purchased this model last week.  About one month ago I purchased the Troy Built 30" model.  I liked everything about it but the chute control.  The joystick just wouldn't work at 90 degree angles.  Lowes took it back without an arguement.  They even knocked $100 off of the John Deere 1130SE.  I haven't gotten a chance to try the John Deere out yet but am tempted to load it up and bring it to a local lake to see if I have similar issues.  This thread is making me nervous.  I'll report back what I find out.
Plasma TVs Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42