Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Deere 826 ID and low tossing distance.

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Deere 826 ID and low tossing distance.
Original Message   Jan 17, 2011 11:47 am
   Picked up a Deere 826 yesterday.  The thing crapped out during the last storm with a brunt belt and the guy hurt is back shoveling so it got the boot. 

   Nice old buzzard rig but I can't find anything on it at the Deere site.  Anyone know where I can an exploded view?  I tried the usual places that have them and nothing on this one.   It's ID plate has P826J, 127489.  If I google P826J I get new models.  Nothing on the other number.

   The thing works fine after a belt replacement but it only tosses 3 - 8 feet with lots of low splatter.  I tried a few different belt sizes and tensions, and even over tight to insure no slip.  I can't see any slip with the cover off.  It has good grab, no crud in the V's, no obstruction in the housing.  It does have quite a distance from the arms to the lining, 1/2 inch.  The impleller is a 4 blade 12 inch and it should toss fairly well, 15-25. 

   Does anyone have this model and could tell me what it tosses like?  I can't see any problems so guess it's a design problem but at 3-8 feet hard to imagine they could make something that bad. 

   The motor certainly is not the problem, a Briggs Intek Snow 11hp a couple of years old.  I can drive into any condition snow and toss the same distance without engine sag.  Very impressive.  Anyone have a URL to an exploded view on the engine?  I can find one so I assume it a special for some maker.  It's got a 3/4 shaft.  3BSXS 3422HT 275387.  I can't get anything found at the Briggs site.  Googling I get 275385 which is a 10hp but nothing for 275487.  There are lots of hits for 3BXSX 3422HT but no motor like this.

This message was modified Jan 17, 2011 by trouts2
Replies: 13 - 22 of 30Next page of topicsPreviousNextNext page of topicsAllView as Outline
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Deere 826 ID and low tossing distance.
Reply #13   Jan 18, 2011 7:42 pm
   It's a decent machine overall.  The linkage rods are not rusted, the tractor internals in great shape, good metal, great cast gearbox, cuts through tough conditions every well but just can't throw. 

  It's an 11 inch impeller in a 12 inch hole.  Ariens has a 10 inch impeller on some machines and if I remember right it it runs at 1410 and the rakes 140.  That is a 4 blade like our machines.  They run it that high to keep up the ft/sec rate out of the chute.  It does very well but the wall space is not like our machines.  On our machines it pretty wide.   Whatever other improvements can be done they will be wasted without first filling the space.  If that alone was done the machine would probably toss well enough to be minimally acceptable.

>>>It would be interesting to know what  throw distance these things were rated for when new. 

    Right.  What bothers me is how could they sell something like this.  It make me think I am missing something because I can't square how they could have sold what we have.

This message was modified Jan 18, 2011 by trouts2
blackdog


Location: The Cross Roads of the Universe....... Des Moines, IA
Joined: Jan 24, 2011
Points: 1

Re: Deere 826 ID and low tossing distance.
Reply #14   Jan 24, 2011 11:42 pm
I too have an 826 mine is serial # 119000, if you go to johndeere.com and search the  ONLINE PARTS CATALOG... try this link  http://jdpc.deere.com/jdpc/servlet/com.deere.u90490.partscatalog.view.servlets.HomePageServlet_Alt                   i loaded the link again and it takes you right to the 826 parts, this might be helpful to some of you.

I came to this site via a google search for info on the blower fan.  It was interesting to read all that you have been writing about the "poor" toss that our snow blowers do.  I am curious did anyone try the auger kit and what where your results?  How about the pulley change did the increased RPMs and help?

I am rebuilding my unit ex. new bushings on augers, new friction disk, new feet or skids, new scrapper bar, points/condensor, belts.  I ahve it tore into 3 pieces...I first went to the above JD site to look at parts...WOW they are expensive!  I did some research and found that I was able to locate all the bushings for 1/3 of what JD wanted at a local bearing dealer, the scrapper bar was $47 to $66 so i made one out of $10 piece of strap and some old spray paint, I bought one foot or skid for $13 and rebuilt the other one, the belts I got both for the price JD wanted for 1 (at the local bearing dealer).  I searched the net to find JD dealer that was the cheapest (as some parts you just cant get any where else)  here is a link to that site..http://www.greenfarmparts.com/  if you find someone cheaper please let me know.

I figured my issue on not moving the snow far was due to all the bad bushings etc....now I am not sure (I should say i have not got it back together and we have not had any snow since i tore it down) that its going to throw the snow any better....I agree that the unit will go through anything and not bog down, but at best with dry snow it will only throw it @15' with the wind, if the snow is wet it wont hardly move it 4'.....

I have a large driveway....over 30' wide and 90' long i really need to move the snow all the way to one side and most of it to one end, needless to say it takes a LONG time to move all that snow several times.  So what I really want to know is have you improved the preformance and if so HOW?????? 

My thought is if this thing aint gonna get it then i am going to buy a model that will before NEXT years snow.

Thanks for any insite and assistance you can muster.

Ken

trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Deere 826 ID and low tossing distance.
Reply #15   Jan 25, 2011 9:12 am

Blackdog, welcome to the forum. 

 

The link you provided shows an 826 that looks like mine from the parts list.  It has the same auger drive pulley and fan dimensions of 11.5 inches with 4 blades.  It’s a looser like mine.

 

>>>I am curious did anyone try the auger kit and what where your results?  How about the pulley change did the increased RPMs and help?

 

I don’t think your poor performance is due to bushings or bearings.  I think it’s a crummy design.  I did not install a “kit” but did put on a 3 inch pulley with the results posted above, lousy.  The impeller speed is still to low to do much.  The machine has a half inch space between the end of the impeller arms and the side wall of the fan housing.  That also has to be taken care of to get good distance. 

 

I stopped working on mine as making mods to that thing is not going to lead to a great machine.  At best the result would be a barely passable machine in average conditions and dog in tough conditions.  It can muscle through snow but it’s a very poor tosser as you know.  It would probably be passable with a 3.5 inch drive pulley.  Once you get the feet per second up high enough you’ll be at it’s max capable RPM on the impeller and augers and only have a barely adequate machine.  It could work though and clear your area but if you are in an area that gets a lot of snow then it would not be a great machine.   

 

There are better machines to spend time on and at least for me that machine was not worth adjusting.  If you started with a better machine and did the same work you would end up with a much better machine.

 

You could try to locate a better blower housing to mount to the base.  The base is very nice.  The tractor section seems very nice with robust components.  The auger engagement clutch is nice and leaves your hand free to work the chute.  For me that engagement is better than the newer designs with drive and auger clutch locking.  On a new machine, if you want to feather the drive clutch in tough going the auger clutch kicks out so you have to hold it.  With the Deere you don’t. 

If you got a full 12 inch or 14 inch impeller and a 3 or 3.5 inch pulley (depends on the pulley size that came with the housing) you would have a viable machine.

 

All in all a 3.5 inch pulley just may be enough to put some life into that thing but it would be at the low end of acceptable.

Dr_Woof


Don't blow into the wind, and don't eat yellow snow. WOOF!

Location: Saskatchewan
Joined: Dec 13, 2010
Points: 253

Re: Deere 826 ID and low tossing distance.
Reply #16   Jan 25, 2011 10:21 am
I have a John Deere 826 that I bought new in 1982.  Model P826H, S/N  101665.  Looks a lot like yours except it Has the H80 Snowking engine.   It doesn't blow snow as far as the new Honda, but goes a lot farther than 8 feet.  I did have problems twice with lack of throwing distance and here is how I fixed them:  (1) about  4 years ago I found that the bearing bushing hole that the impeller shaft rides in had worn into an oval shape so that  when activating the auger drive control (this just tightens the belt) the auger shaft moved up in the bearing and never could get proper tension on it.  Replaced the bushing (and all the others while I was at it) and all was good.   And then (2)  Earlier this winter the throwing distance dropped to what you are seeing - snow just dribbling outa the chute.   Had put a new belt on it last year and looks like it has stretched.  Easy fix this time - just tightened up the ball linkage a few truns to the specs in the repair manual and this fixed the problem.  Took a few tries to get it just right and this appears to be a sensitive adjustment:  too loose and the impeller still turns but it won't throw snow, too tight and you'll get a sore wrist forcing the drive control up and probably be replacing bushings again sometime soon.  All told, this has been a good blower for me.  Not as good as the new Honda tracker, but certainly better than the new JD 1330SE that I tried earlier this year.  I still use it when conditions don't require the Honda.

ahw2698


Joined: Jan 17, 2011
Points: 6

Re: Deere 826 ID and low tossing distance.
Reply #17   Jan 31, 2011 9:35 pm
I just finished installing a Clarence Impeller Kit on my John Deere 826. We are supposed to get snow tomorrow and Weds. so I should have ample opportunity to test it out.

I ran it for a while tonight  just to "break in"  the rubber onto the housing and that went fine.

jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Deere 826 ID and low tossing distance.
Reply #18   Jan 31, 2011 10:58 pm
If you have a 1/2" space between the impeller blade tips and the housing that is the problem, without question.  Increasing the rpm won't really help that much. The impeller and housing section of a
blower is basically a pump. And without a fairly tight clearance it won't pump well. Not only that,  the impeller is always spinning inside a wad of snow that never leaves the housing.  It's functioning more like a blender than a pump.

 I had an air drill once that had worn vanes.  It would spin really fast and sounded like it was working well until.
You put the drill under a load by putting the drill bit on a piece of steel.  It would barely spin then. All the air that was supposed to be pushing on the vanes to spin the chuck was finding an easier way out by going through the space between the vanes and the housing. I know that is kind of the reverse of how a impeller and housing work but it's a similar principle.

I recently posted a comment from a Ariens tech that I read somewhere else.  He stated that "if the clearance is correct in the housing you should be able to put a dime on the bottom of the housing and the impeller should sweep it up and throw it out the chute". "When the Impeller won't do the same with a quarter it's time to rebuild the impeller blades". 

When I lengthened the blades on my impeller to where I now have 1/16 to 1/8" clearance (the housing isn't perfectly round) it made a noticeable difference in the throw distance and the ability of the blower to blow both snow and slush.  So much so that I no longer carry a clean out tool on the blower.  The chute just never clogs and I can throw pure slush. 
I really think that decreasing the gap or clearance between the impeller blades and housing is the single biggest performance booster that can be made on a blower.  You can't believe the difference until you see it for yourself.   I've also noticed that because the blower is now so much more efficient at expelling all the snow that enters the housing.  That I can reduce the engine speed, use a higher gear and still get the job done with snow depths up to about 4 or 5". It's a wonderful thing!
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Deere 826 ID and low tossing distance.
Reply #19   Feb 1, 2011 2:23 pm

Jrtrebor:>>If you have a 1/2" space between the impeller blade tips and the housing that is the problem, without question.

 

I agree.   The spacing and the very slow impeller rpm make a big problem.

 

   There are now five people I have heard of that have this style of Deere and have the distance problem.  A guy on another forum put CL’s kit in and is using his but he did not give the improvement over the original short distance.  Reading about his made me think about mine more.  I checked the impeller area again and realized I had ½ on one side and an inch on the other at 180 from the ½. 

   The impeller arms are very small to boot.  With a CL kit it would be good to extend past the flat up onto the curved part of the arm.  If mine got a kit I’d still be away from the barrel on 1/3 of the travel of the impeller.  I think mine has it’s impeller shaft hole slightly off from center.

Shryp


Location: Cleveland, OH
Joined: Jul 26, 2010
Points: 532

Re: Deere 826 ID and low tossing distance.
Reply #20   Feb 1, 2011 2:42 pm
I read it is straight down to 90 degrees out to the side of the chute that matters.  It was said that the rest doesn't matter.
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Deere 826 ID and low tossing distance.
Reply #21   Feb 1, 2011 3:24 pm
Sorry Shryp, can you repeat that but differently?

Is that the last quarter of rotation before the chute?

This message was modified Feb 1, 2011 by trouts2
Shryp


Location: Cleveland, OH
Joined: Jul 26, 2010
Points: 532

Re: Deere 826 ID and low tossing distance.
Reply #22   Feb 1, 2011 4:23 pm
Yea, I read somewhere that it is the last quarter of the sweep that really matters.
Replies: 13 - 22 of 30Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42