Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Toro CCR 2000, no spark from plug wire

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
Denny


Joined: Dec 12, 2007
Points: 7

Toro CCR 2000, no spark from plug wire
Original Message   Dec 12, 2007 8:14 pm
I turned the key on and have no spark from the plug or even the plug wire when turning over the engine

How do I know if it is the coil magneto or the xstar module magneto?

It is a model 38180

Replies: 5 - 14 of 77Next page of topicsPreviousNextNext page of topicsAllView as Outline
niper99


Location: London Ont
Joined: Dec 2, 2007
Points: 354

Re: Toro CCR 2000, no spark from plug wire
Reply #5   Dec 14, 2007 12:47 am
l didn't reliaze that you hade a seperate igntion module l'm not exactly sure how to test that, but if l had to bet on it l would replace the module 90% sure.  maybe u should take it to a shop to make sure 140.00 dollaurs ain't  a cheap guess
Denny


Joined: Dec 12, 2007
Points: 7

Re: Toro CCR 2000, no spark from plug wire
Reply #6   Dec 21, 2007 6:41 pm
I replaced electronic/magneto box/ignition module with a generic Stens Mega Fire II. I know have spark at the plug, I didn't't before.

I gapped the plug and put it in. I now start the engine (using 100% gas to test)

It starts a little then misfires and sometimes backfires. It doesn't stay running.

The paperwork for the Mega Fire says it may not work with more than one magnet in the flywheel, (I have three).

Do you think I might need the Toro OEM magneto module for timing purpose.
Could it be because the 100% gas?

The resistance/ohm check for the coil was 1.1 ohms from one coil to gnd then 11K ohms to the plug wire. I think the coil good as the original problem was no spark and now I have spark after the module change.
mech12


Joined: Feb 20, 2006
Points: 273

Re: Toro CCR 2000, no spark from plug wire
Reply #7   Dec 22, 2007 5:25 pm
  yes,  the only thing that mega fire does is to replace points and a condensor.  if you have an external "timimg" module  you cant overide that with this mega fire.   that suzuki engine with break your bank.  
Denny


Joined: Dec 12, 2007
Points: 7

Re: Toro CCR 2000, no spark from plug wire FIXED
Reply #8   Dec 23, 2007 5:55 pm
FIXED!!!!!!!I had to scrape some paint to get a good ground and reverse the wires on the "universal" ignitor (Mega Fire II) $15.00 vs. $110.00 OEM

Blowin snow, thanks

miller87


Joined: Feb 12, 2010
Points: 6

Re: Toro CCR 2000, no spark from plug wire
Reply #9   Feb 12, 2010 8:10 pm
I realize this post is old and Denny may no longer be on this board, but I had to ask.  I seem to have the same problem and the shop wanted about $140 for the Toro 81-0340
Xstar Module-Magneto.  Including labor it was pushing $200 and I only paid $75 for this eight years ago.  I just can't see putting that much into this machine so after reading this post I asked them to order the Stens Mega Fire II 440465 ignition module for $18 and I'll install it myself.  So if Denny is still out there or anyone else who has experience with this part, I'd like to know if it is durable in this application.

Which wiring method do I use, the negative ground or positive ground? See the wiring diagram at http://www.rcpw.com/kawasaki-ignition-coils-parts/440465.html.  Click on the 2nd thumbnail pic for the diagram.

Thanks!

(The machine in question is a 1987 Toro CCR2000, model 38180)

miller87


Joined: Feb 12, 2010
Points: 6

Re: Toro CCR 2000, no spark from plug wire
Reply #10   Feb 17, 2010 10:16 pm
Update.  I bought the part mentioned in this thread, the Mega Fire II universal ignition module (http://www.rcpw.com/kawasaki-ignition-coils-parts/440465.html).  I actually got it from my local Toro shop.  I installed it with the negative ground wiring as shown in the installation diagram.  I decided to install the module up near the spark plug access cover instead of under the engine near the auger as the original part was.  Since I'm not sure of the durability of the part in this application, I wanted to make it easy to replace it if it fails.

From what I can tell, the original part (Toro Xstar Module-Magneto 81-0340) was grounded by its metal case with the two screws that held it to the engine block.  I grounded the new module with the included bare-end wire.  I clamped the bare wire (which I stripped to about 1") under the bolt holding the key switch ground wire.  I applied dielectric grease to all connections.  I'll secure the module body with a wire so it stays in place yet is isolated from engine heat and vibration.  It seems like the old module failed when the engine was hot and I figured minimizing vibration couldn't hurt.

I'll post pictures once I get it done if I can do it on this site.

hosed


Joined: Feb 19, 2010
Points: 2

Re: Toro CCR 2000, no spark from plug wire
Reply #11   Feb 19, 2010 3:25 am
Miller87,
Did the Mega Fire ii work for you? How does the engine run with it?  Curious to know if this $20 part really will replace a $140 Toro module.
Thanks
miller87


Joined: Feb 12, 2010
Points: 6

Re: Toro CCR 2000, no spark from plug wire
Reply #12   Feb 19, 2010 11:11 am
hosed, after installing the new module I started the engine a few times and from what I could tell, it ran the same as it always had.  I didn't blow any snow yet since I haven't put the shrouds back on yet.  I am going to put it all back together today and then give it a real test.  I'll post again.

In another post by Denny, I think on this site, he mentioned the key switch operated in the opposite way, but I did not find that in my case.  On is still on and off is off.

miller87


Joined: Feb 12, 2010
Points: 6

Re: Toro CCR 2000, no spark from plug wire
Reply #13   Feb 19, 2010 6:22 pm
Ok, I put it all back together and so far it runs as well as ever.  I ran it to clear some fairly dense snow near the street that I shoveled off the high banks to widen the entrance and it worked great and started each time after I shut it off.  A huge frustration of the old module is that the engine would never start when the module was hot.  Pulling the spark plug and drying it with a lighter did seem to get it going, but what a pain that was so I would never shut it off until I was all done.  I wish I knew of this fix several years ago when it started acting up.

I'm no expert at this stuff, but so far I'm really happy with this module and I could buy seven of them for the cost of the Toro part.  Thanks, Denny, where ever you are!

I'll figure out how to post pics and do that next.

miller87


Joined: Feb 12, 2010
Points: 6

Re: Toro CCR 2000, no spark from plug wire
Reply #14   Feb 20, 2010 11:53 am
This picture shows the original part mounted on the bottom of the engne near the chute.  It's the small brass box in the middle of the pic.

This is the Mega Fire II module.  I used a twist tie to hang it from the wires up by the key switch plug.  After installing the control panel I verified that the wires didn't interfere with the pull cord etc.

The yellow arrow points to the ground wire for the new module clamped under the same bolt used to ground the key switch.  You can see how easy it would be to replace the module if needed.  I considered getting a ring type wire connector and I still might.  That's what the key switch ground wire uses.  I could have installed the new module in the factory location, but would have needed 1/4" longer screws and decided against that for the reasons I mentioned in previous posts.

Here's a link for a short vid of the machine running.

http://s852.photobucket.com/albums/ab90/miller87a/Toro%20CCR2000/?action=view&current=DSCF0168.flv

So that's about it.  I'll let you know if anything goes wrong.  I don't know the durability of this module, but since I mounted it for easy replacement, it will probably never fail, haha.

If anyone can explain how this part of the ignition system works, I'd like to hear it.  Thanks.

Replies: 5 - 14 of 77Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42