Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Just got Ariens ST824, need some advice on repairs

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Just got Ariens ST824, need some advice on repairs
Original Message   Nov 9, 2011 8:57 pm
Hi all,

I just bought a 1993 (I think?) Ariens ST824. Model 924082, serial 0040XX.

The good news: Paid $150, the augers weren't turning (the belt had come off, and seems like it needs to be replaced). It starts & runs fine, and has electric start. The engine showed ~120-130 psi when cranking it with the electric starter, and ~60 psi when pulling it by hand (I don't know whether those are good or bad). It has a differential, rather than the simple pin-through-the-axle setup of my MTD. I thought that was a cool surprise, I didn't expect a differential. Is that common on the ST824's, or did I get lucky? The differential works fine. It's a weird feeling being able to just steer it.  I get the impression that the previous owner gave it some grease occasionally, since the gearbox area seems well lubricated. The person I bought it from just got it recently, so I don't know its history.

The less-good news: It has a fair bit of rust, unfortunately (may have been stored outside?). But it seems solid. There are two areas that concern me so far.

One is that the big gear on the differential can skip against the teeth of the mating sprocket. There appears to be quite a bit of play in the wheel bearing on that side (the bearing at the other end of the shaft, for the right wheel, seems a bit better). So I think the shaft is being allowed to move too far away from the mating sprocket, and it's able to skip. Is this common? It looks to me like replacing the wheel bearing should do quite a bit to help make the gears tight again. Am I right? Is that a difficult job? Special tools needed, etc? It sounds like a tapered roll pin has to come out, from glancing at the service manual. 

The other issue is that there is play between the two halves of the unit. The tractor half, and the snowblower half. The big bolts at the top of the frame, which join the two, were loose, and able to bang back & forth. It seems that it's been used like that for a while now, unfortunately. One of those bolts can't be tightened, the nut (below the frame) just spins. I'm having a hard time figuring out a part number for that nut. As a result of those bolts being loose, I assume, the bottom area, where the two halves join, has also worn. There is a rod in the tractor half which slips into a groove in the snow blower half. That groove has opened (I think) and the rod has worn smaller. So there is play down there as well. I'm not sure if there's a good way to try and take up that play, with some kind of bushing perhaps.

So I think I need at least some belts, a friction disk, probably one wheel bearing (I'd prefer to leave the right-side one alone, if possible), and I'm sure some other random parts. Maybe I can figure out some way to tighten up that rod-to-groove fit at the bottom.

Does this sound like it's worth fixing up? I'm looking for something reliable and durable to replace my MTD 8 hp, 26". I just don't know whether the issues described above should really never happen, and therefore this machine has been put through a LOT. And that maybe I should look for a different one. I don't have a problem fixing this stuff, as long as a handy homeowner can replace the bearing, and so on. I just don't want to start down a rabbit hole.

Thank you for any feedback or suggestions!
This message was modified Nov 15, 2011 by RedOctobyr
Replies: 23 - 23 of 23Next page of topicsPreviousAllView as Outline
manjestic


Location: North Shore, MA
Joined: Oct 31, 2011
Points: 87

Re: Just got Ariens ST824, need some advice on repairs
Reply #23   Nov 28, 2011 10:31 pm
RedOctobyr wrote:
I may try one of the rust treatment/protector products for this winter. Painting it seems like a big undertaking. I wonder if Ariens makes touch-up paint that you can brush on, for addressing little areas without having to mask things nearby.

I did some spot painting of the chute and auger housing with great results, with a spray can.  Granted, I completely disassembled the attachment, but I think some wet sanding with 2000 grit will take care of overspray.  I sanded and primed and then used Chevy Orange Engine Enamel.  Though it matches quite well, I wonder if Hemi Orange isn't a better match.

http://rustoleum.com/CBGProduct.asp?pid=372
This message was modified Nov 28, 2011 by manjestic
Replies: 23 - 23 of 23Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42