Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Video of my Ariens blowing snow

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Video of my Ariens blowing snow
Original Message   Feb 24, 2011 7:04 pm
Well I was finally able to get some video of my blower in action.  Went out to our family cottage and one of my neighbors was kind enough to operate the camera for me.
I'm pretty satisfied with the way it performs after the repower and other modifications to the impeller blades and housing. I had also increased the auger drive pulley size from
the stock 2 3/4" to 3 1/4". Powered chute controls work great.  I also came up with a way to use the old deflector control lever to operate the auger engage/ disengage.
So now I can pull on the lever engage the blower and not have to keep the right handle held down all the time.  It's so much easier to use the chute control joystick and hold on
to the blower.  I believe that it is also easier on the belt with fewer engage and disengage cycles.

I think it is still a little underpowered.  It could probably use a 13hp instead of the 11hp.  That 32" bucket takes in a lot of snow.  I'd also like to increase the auger drive pulley
to a 3 1/2" just to see what happens.  The one issue or component I still haven't come to a conclusion about is the impeller (14").  It has 6 blades, it's the only six bladed impeller I've
ever seen.  A lot of the newer blowers and the Honda's have only three blades.  I know how well the Honda's perform and I've watched a couple videos of the Ariens Compact 22
going through 14, 16" inches of light new snow without a problem.  So I've been wondering if six blades is just over kill and a lot of extra mass and weight to be turning. Once you get them
spinning I guess inertia is on your side.  But if three works well, and Honda first proved that they do.  Then what is the advantage of 4 or 6, just don't know.  One thing I do know is that.
The blade tip to housing clearance is a really important factor in blower performance. As is the impeller RPM.

Just a little information about the video.   In the first section the depth was about 18" deep in the plow roll of pile. And around 14 or 15" deep everywhere else. The snow was about three day old.
Had a bottom layer (2") of heavier stuff.  It had settled and was somewhat compacted and dense.  Not light power by any means but also not high in moisture and wet heavy.
Any and all comments are welcomed!
This message was modified Feb 24, 2011 by jrtrebor
Replies: 26 - 29 of 29Next page of topicsPreviousAllView as Outline
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Video of my Ariens blowing snow
Reply #26   Mar 2, 2011 6:41 pm
GtWtNorth
I did/do have the "automatic locking of the auger lever when you hold down the drive lever" But it can be kind of a pain.  I got spoiled by the controls on the old Ariens I had.
Here are a few photos of my current set up for engaging/disengaging the blower.

     Engaged                                 Disengaged

    

Looking up, underneath the dash from the right side.
This was all part of the original Deflector control setup.
(that is not the way the cable originally hooked into the bracket I accidently cut off the wrong end of the cable. The end your seeing actually hooked onto a bracket on the chute, OOPs)

Cable is connected to the handle        Cable hooked into existing bracket
      


 1)  I pulled the inner cable out of the sheath to cut the sheath to the right length then shoved the inner cable back in the sheath.
2)  Cut the inner cable wire leaving about 4 or 5"of wire hanging out beyond the end of the sheath. (the inner cable is solid wire not braided cable)
(This initial cutting was done before the cable was installed on the blower).
3)  Measured things, re-cut the inner cable, bent a hook on the end and hooked it onto the chain.

    

I did have to tighten the nut that increases the friction in the control lever so it will hold in place.
When the blower is engaged and there is spring tension pulling against it.
It works really well, and I love being able to disengage the blower without having
to release the left hand lever and stop my forward or backward motion.

Paul7


Joined: Mar 12, 2007
Points: 452

Re: Video of my Ariens blowing snow
Reply #27   Mar 3, 2011 5:18 pm
jrtrebor wrote:

My thinking was that if I could increase the thruput a little more by increasing the auger and impeller speeds. Maybe that would match up with the forward speed in first gear. (which is just a tad to fast in certain snow type conditions). But as you know increasing the thruput by using a larger pulley will pull more power out of the engine.


I saw the video.  You don't need to increase anything.  The last thing you need is more power.  I saw one tree that was already knocked over...it probably couldn't stand up to the force of the snow you were hitting it with. 

Put down your wrenches, back away from your snow cannon, and lets save some trees. lol.
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Video of my Ariens blowing snow
Reply #28   Mar 3, 2011 9:24 pm
Paul7 wrote:
I saw the video.  You don't need to increase anything.  The last thing you need is more power.  I saw one tree that was already knocked over...it probably couldn't stand up to the force of the snow you were hitting it with. 

Put down your wrenches, back away from your snow cannon, and lets save some trees. lol.

I got a good laugh out of that. Thanks!
GtWtNorth


https://t.me/pump_upp

Location: https://t.me/pump_upp
Joined: Nov 16, 2008
Points: 264

Re: Video of my Ariens blowing snow
Reply #29   Mar 4, 2011 9:41 am
jrtrebor - thanks for the photos, nice job as usual. Since I don't have the chute control on mine to re-purpose,  I'll keep my eye open for one of the older style machines that I can get the controls from.Looking at the photos gave me another idea. Since you have a battery aboard, you may be able to use a 12V solenoid & switch to activate the arm of the auger clutch instead of using the lever & cable?

Anyway, I agree with Paul7, take it easy on mother nature.

Cheers

https://t.me/pump_upp
Replies: 26 - 29 of 29Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42