Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Craftsman 8/24 snowblower - Auger rake rusted on shaft - help!

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
CuriousGeorge


Joined: Nov 20, 2009
Points: 3

Craftsman 8/24 snowblower - Auger rake rusted on shaft - help!
Original Message   Nov 21, 2009 1:05 am
Hello folks,
Very happy to have found a great site full of experienced OPE people.

I've recently purchased a 20 or so year old Craftsman 24" snowblower, never having owned one before and not knowing much about them. It was on the cheaper side of what was out there, it started, and ran, so I said "I'll take it!" To not make a short story long, I started bouncing around the internets, learning about snowblowers, and checking the basics.

The one thing I've been stuck on is the left side auger rake being completely rusted onto it's shaft. The shear bolt was completely rusted in as well, so I had to drill it out on both sides.

So-far I've tried lots or penetrating lubricant, hammering, heat as well as two types of gear pullers against the shaft end. No go, will not budge. Not even a bit.


http://curious0george.smugmug.com/Machines/Craftsman-824/10387892_JWKgi#719377758_g5EhW


The right side shear bolt came right out, and the auger spins perfectly fine on the shaft. There are no grease fittings on this model.

Anyone out there have any ideas as to what I can try to get this auger off the shaft? Any tips or tricks that I can try? I suppose I can just leave it as is, but from what I am reading it could cause big issues, if the auger decided to eat something different than snow.


Thanks all, looking forward to your replies, keep up the great work!




Replies: 4 - 5 of 5Next page of topicsPreviousAllView as Outline
CuriousGeorge


Joined: Nov 20, 2009
Points: 3

Re: Craftsman 8/24 snowblower - Auger rake rusted on shaft - help!
Reply #4   Dec 4, 2009 5:13 pm
JohnnyBoyUpNorth wrote:
I had that happen once. I pulled the shear pins out and ran the machine quickly in heavy wet snow. That freed them.

Thanks for the reply JohnnyBoyUpNorth, I wish it were that simple, I've tried 3 different kinds of gear pullers, damaging one with a 3 foot extension bar, so this sucker ain't giving up that easily!!!

On the other hand, maybe running the auger without a shear bolt (as I had to drill it out on both sides), temperature variations and material stress might loosen things up...

Cheers!
JohnnyBoyUpNorth


Location: New Brunswick Canada
Joined: Dec 30, 2007
Points: 72

Re: Craftsman 8/24 snowblower - Auger rake rusted on shaft - help!
Reply #5   Dec 4, 2009 7:57 pm
There's a product called Deep Creep, made by Seafoam. If you're in Canada it can be purchased at NAPA stores. It's amazing. If any penetrant will break it loose, it's that stuff. I would try that stuff. Google "seafoam" and you'll find plenty of info on it.

I've been in similar situations where I've wanted something to happen. That something might be a frozen nut that I've wanted removed, a tire off a wheel or something of seemingly profound importance at the time. I've been known to grab torches, sledgehammers and angle grinders and react with speed and violence where a little common sense would have done it. Sometimes my time in the military isn't an asset...

That said, can you find an old junked snowblower that you can use for parts? If I spent a quarter of my cage time with these fool machines using my head, a solution would easily present itself elsewhere. 20 year old Craftsman snowblowers can't be a rarity yet.

Just a thought.

Contents under pressure....
Replies: 4 - 5 of 5Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42