Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > honda hs 1132 pulls hard to one side

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
dfvellone


Joined: Jan 10, 2009
Points: 20

honda hs 1132 pulls hard to one side
Original Message   Jan 10, 2009 12:41 am
Hi all, new to this forum after having searched for a solution to my surging hs 1132.
Among the several problems I've had with this machine is the severe pulling to the right when the bucket is in the mid or low position. I've put it on a flat surface and adjusted the shoes and scraper to manual specs and no luck. Shoes are even and scraper is even so no misalignment there. I've tried to adjust the shoes and scraper to counter the pull but nothing worked. Track tension is even. This is a pretty frustrating problem as I clean a long drive and fight against the pull the whole time - tiring and forget it if my wife ever has to run the machine. As usual, my honda dealer is no help whatsoever. I had to inform them of the icing kit I learned of on this forum after three years of bugging them about the surging, backfiring problem I was having.
Replies: 1 - 10 of 34NextNext page of topicsAllView as Outline
nhmatt


Joined: Dec 21, 2008
Points: 104

Re: honda hs 1132 pulls hard to one side
Reply #1   Jan 10, 2009 8:58 am
Is it scraping on the ground as you drive? If you position it with the bucket in air is the problem stillthere?   There's no differential so unless there's a problem with the actual rubber trac I don't think that's it either.  My unit seems to want to pull into the direction of harder snow, as the bucket gets snagged on that corner but it doesn't sound like that's your problem.  I've got the same issue with my wheeled ariens.
Knee_Biter


Wicked Pissa

Location: just outside of BOSTON
Joined: Dec 14, 2008
Points: 147

Re: honda hs 1132 pulls hard to one side
Reply #2   Jan 10, 2009 9:19 am
We have an 1132 at work and the first thing I noticed last year while using it for the first time was it surged up and down unless the choke was pulled out just a touch. Second thing was it pulled to the right extremely bad. Everything was adjusted to spec. I ordered the optional side skids and installed them. It fixed the pulling. I love the wheeled Honda units but really do not like the tracked machines. I would rather my personal wheeled hs624 over a brand new 1132.

nhmatt


Joined: Dec 21, 2008
Points: 104

Re: honda hs 1132 pulls hard to one side
Reply #3   Jan 10, 2009 9:42 am
I think the idea of the rear shoes is to be in line with the path of the wheels.  I had a 828 wheeled honda that when I backed it up into my shed I would occasionally clip one of the shoes (easily done in reverse) on the edge of the wood, and that would bend the shoe and then my bucket wouldn't be straight.  The shoes on my 1132 are MUCH thicker and I think I'd have less of an issue with this, but then again this machine is much heavier and would probably do the same thing if you snagged and edge going backwards.

I think the side shoes would fix this.  I  can't think of any real advantage to the original shoes, but maybe they keep support under the center of the bucket so as you go under uneven ground the middle scraper edge isn't getting hammered as much.

This message was modified Jan 10, 2009 by nhmatt
dfvellone


Joined: Jan 10, 2009
Points: 20

Re: honda hs 1132 pulls hard to one side
Reply #4   Jan 10, 2009 6:37 pm
Thanks for the replies. I plan on ordering the optional side mounted tracks and hopefully that will fix the problem. I cleaned my pond off today for skating - nice level surface- and the pull to the right was extreme.
borat


Joined: Nov 10, 2007
Points: 2692

Re: honda hs 1132 pulls hard to one side
Reply #5   Jan 10, 2009 6:51 pm
If it's pulling that badly on sheer ice, it sound more like a drive issue than skids.   Have you tried jacking the machine up off of the ground to see if there might be a problem with one of your drive wheels.  If it pulls strongly to the right, the right side wheel/track mechanism might be compromised.  Does your Honda have plastic or metal drive wheels?  Do the drive wheels have splines or a pin through them to lock onto the drive axle?   If it's pulling as badly as you say, I'd be taking a close look at the drive components. 
dfvellone


Joined: Jan 10, 2009
Points: 20

Re: honda hs 1132 pulls hard to one side
Reply #6   Jan 11, 2009 12:37 am
borat wrote:
If it's pulling that badly on sheer ice, it sound more like a drive issue than skids.   Have you tried jacking the machine up off of the ground to see if there might be a problem with one of your drive wheels.  If it pulls strongly to the right, the right side wheel/track mechanism might be compromised.  Does your Honda have plastic or metal drive wheels?  Do the drive wheels have splines or a pin through them to lock onto the drive axle?   If it's pulling as badly as you say, I'd be taking a close look at the drive components. 
 
A drive issue is what I was thinking since no matter how I adjusted the shoes or scraper the machine still pulled.
The tracks are in good shape. Wheels are plastic and everything seems to be ok with them.
I've got to get the shop manual to see what kind of adjustments might be made to the drive components. The machine is a misery to use unless it's in the high position.
aa335


Joined: Nov 29, 2008
Points: 2434

Re: honda hs 1132 pulls hard to one side
Reply #7   Jan 11, 2009 12:14 pm
borat wrote:
If it's pulling that badly on sheer ice, it sound more like a drive issue than skids.   Have you tried jacking the machine up off of the ground to see if there might be a problem with one of your drive wheels.  If it pulls strongly to the right, the right side wheel/track mechanism might be compromised.  Does your Honda have plastic or metal drive wheels?  Do the drive wheels have splines or a pin through them to lock onto the drive axle?   If it's pulling as badly as you say, I'd be taking a close look at the drive components. 

I think this is the most likely problem.  One of the pins that lock the shaft to the crawler wheels may have been sheared.  Essentially, power is only delivered to one side of the tracks.
dfvellone


Joined: Jan 10, 2009
Points: 20

Re: honda hs 1132 pulls hard to one side
Reply #8   Jan 11, 2009 2:19 pm
aa335 wrote:
I think this is the most likely problem.  One of the pins that lock the shaft to the crawler wheels may have been sheared.  Essentially, power is only delivered to one side of the tracks.
Nothing sheared and the shaft/wheel assembly appears to be sound. I just got in from checking it all out and one thing I notice is that when the machine is in the high position and you try rocking the handles nothing moves - the tracks appear to be even on the ground. But when I lower it to mid or low I can push down on the handles and the machine rocks as though the tracks aren't resting evenly. Everything visually seems in order so all I can guess is that possibly somethings warped. It's been like this from the get go but i don't usually clean in the lower positions because I have stone mix driveway surface.

Have to say though that having much experience with honda power equipment, for the cost of this machine I'm not impressed and regret purchasing it. My dealer just sold me the de-icing carb kit and they wouldn't warranty  it even though I've been complaining about engine surging, backfiring, and occasional loss of power since my first season with the blower. I understand honda posted a bulletin on this kit because of problems with icing in the carb. $2400 blower (3k today!) and they make me purchase a fix for honda dropping the ball on engineering on this model.

  
aa335


Joined: Nov 29, 2008
Points: 2434

Re: honda hs 1132 pulls hard to one side
Reply #9   Jan 11, 2009 4:10 pm
dfvellone wrote:
Nothing sheared and the shaft/wheel assembly appears to be sound. I just got in from checking it all out and one thing I notice is that when the machine is in the high position and you try rocking the handles nothing moves - the tracks appear to be even on the ground. But when I lower it to mid or low I can push down on the handles and the machine rocks as though the tracks aren't resting evenly. Everything visually seems in order so all I can guess is that possibly somethings warped. It's been like this from the get go but i don't usually clean in the lower positions because I have stone mix driveway surface.

Have to say though that having much experience with honda power equipment, for the cost of this machine I'm not impressed and regret purchasing it. My dealer just sold me the de-icing carb kit and they wouldn't warranty  it even though I've been complaining about engine surging, backfiring, and occasional loss of power since my first season with the blower. I understand honda posted a bulletin on this kit because of problems with icing in the carb. $2400 blower (3k today!) and they make me purchase a fix for honda dropping the ball on engineering on this model.

  

Yes, it will rock a bit, about 1/4 to 1 inch at most.  I thought my bucket/chassis was bent when I first did this, but after close examination, I found that the rocking was due to the two tracks not in synch with one another. The two track contact points (ridges) are not always the same.  In addition the two rear skid shoes are right behind the bucket, just a few inches in front of the tracks.    I now have the side skid shoes and the rocking have disappeared.

Can you try to turn it with the engine off and the bucket up?  Do you find that it is harder to turn left than turning right?

This message was modified Jan 11, 2009 by aa335
Knee_Biter


Wicked Pissa

Location: just outside of BOSTON
Joined: Dec 14, 2008
Points: 147

Re: honda hs 1132 pulls hard to one side
Reply #10   Jan 11, 2009 6:45 pm
I am telling you. I honestly hate the tracked Honda's. I think the 928 wheeled machine is the one to get. I have the 624 wheeled at home and love it. Brand new 11hp tracked at work and I try not to use it and use the Ariens when it will move. I agree that for the money you spent it should be perfect. The only plus is that if you list it on Craigslist you can sell it quick at a little loss and buy the 928 wheeled unit that I would bet the farm you would love. But once soured you might never want a honda product again.
This message was modified Jan 11, 2009 by Knee_Biter


Replies: 1 - 10 of 34NextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42