Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Jammed Toro

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
Dee_M


Joined: Nov 27, 2008
Points: 2

Jammed Toro
Original Message   Nov 27, 2008 11:12 am
Hi all. I am very new to using things such as snow blowers, and so I have definitely never fixed one! (widow for 2 yrs after 35 yrs) Yesterday, while clearing the snow from the patio, it ate my dog's "rope toy". (A heavy rope with large knots at each end.) The rope is jammed in behind the blades (which scare the life out of me) behind a piece of metal, blocking the snow chute. Are these things easy to take apart, do I need to hire someone, or get a new SB? My son will look at it after he finishes work, but in the mean time I'm trapped in the driveway. I've been told to take out the shear pins (not sure what they are) and rotate the blades. Any suggestions? I've already considered moving to an apt.

This message was modified Nov 27, 2008 by Dee_M
Replies: 2 - 3 of 3Next page of topicsPreviousAllView as Outline
pvrp


Joined: Nov 14, 2008
Points: 151

Re: Jammed Toro
Reply #2   Nov 27, 2008 2:46 pm
I don't see the necessity of removing any pins.  The impeller (the part where the toy
is jammed) normally turns fairly easily, with some resistance from the brake pad that
rubs on the pulley on the other side of the rear wall.  It's the auger rakes (the spiral
things up front) which won't turn without removing pins.  You could tie the auger
control on the handles in the engaged position which will release the brake.

First remove a key if there is one from the snowblower then remove the spark plug
wire from the spark plug (there's sometimes a little post on the engine that it can be
grounded to, otherwise just make sure the wire is far from the plug).   Actually, it
would be best to remove the sparkplug as this will let the engine turn fairly easily
which will help with the following.  Then find some way to turn the impeller in the
opposite direction to its normal direction.  Maybe tap on it with a rubber mallet if
you can get one in there, careful not to bend the blades, though they look pretty thick.

A razor knife could be used to cut out as much of the toy as possible beforehand.

If all this fails then split the machine apart in the middle so you can turn the pulley
behind the impeller.

I can't help but think that if one were to design a thing that would be almost
guaranteed to jam a snowblower that dog toy would be it...

Good luck. 

Paul

This message was modified Nov 27, 2008 by pvrp
borat


Joined: Nov 10, 2007
Points: 2692

Re: Jammed Toro
Reply #3   Nov 28, 2008 8:30 pm
Get your son to take a good sharp utility knife and make as many cuts as necessary to dislodge the rope.  Cut as close as possible to the vanes.  Once the large pieces of rope are out, when you run the machine,the vanes will eject the small pieces left behind.  Spray a little WD40 on the jambed pieces of rope stuck between the vanes and the impeller housing.  It will reduce friction to let the impeller spin easier.  After clearing the rope, make sure there are no bent vanes  or broke welds on the impeller.  Next tip:  No more rope dog toys outside. 
Replies: 2 - 3 of 3Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42