Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > No grease zerks on Ariens 926le auger shaft

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
blomberg91


Location: Talkeetna, Alaska
Joined: Nov 22, 2011
Points: 9

No grease zerks on Ariens 926le auger shaft
Original Message   Feb 21, 2012 3:40 am
Unlike my old school Craftsman, there are no grease zerks on the auger shaft on my Ariens. I read all the time on this forum about people digging into frozen augers, shafts, and gearboxes. I am thinking about drilling, tapping, and fitting the auger blades with a grease zerk on each side of the gear box so I do not have to break down the entire auger every time to lubricate the shaft. At the end of the season do you experienced snowblower hands break down the entire auger assembly to inspect, clean and grease it? If that is the case, putting in the grease zerks would be futile.   
This message was modified Feb 21, 2012 by blomberg91
Replies: 2 - 5 of 5Next page of topicsPreviousAllView as Outline
RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Re: No grease zerks on Ariens 926le auger shaft
Reply #2   Feb 21, 2012 10:44 am
Just in terms of what people do, I personally don't pull the machine apart at the end of the year. My MTD did not have grease zerks. I hopefully put some grease on the shafts when I last had them apart ~9 years ago, but I couldn't say for certain. They haven't been removed since They are also still free on the shaft. They can move around a little bit on the shaft, which may help. If they had a nice snug fit, and did not wiggle on the shaft, I'd expect they'd rust solid much more easily and sooner. I do store it indoors, so its out of the weather.

If you can add zerks easily, it certainly wouldn't hurt. Worst case, at the end of the season, you could try to spray/drip some oil into the shafts, from the ends, then remove the shear pins and spin the augers on the shafts? That would both help to distribute the oil, and also maybe knock down the rust that was forming.
Snowmann


Joined: Dec 3, 2003
Points: 494

Re: No grease zerks on Ariens 926le auger shaft
Reply #3   Feb 21, 2012 10:27 pm
blomberg91 wrote:
Unlike my old school Craftsman, there are no grease zerks on the auger shaft on my Ariens. I read all the time on this forum about people digging into frozen augers, shafts, and gearboxes. I am thinking about drilling, tapping, and fitting the auger blades with a grease zerk on each side of the gear box so I do not have to break down the entire auger every time to lubricate the shaft. At the end of the season do you experienced snowblower hands break down the entire auger assembly to inspect, clean and grease it? If that is the case, putting in the grease zerks would be futile.   


What is your model and serial number?
blomberg91


Location: Talkeetna, Alaska
Joined: Nov 22, 2011
Points: 9

Re: No grease zerks on Ariens 926le auger shaft
Reply #4   Feb 22, 2012 12:32 am
I am at work for the next week straight but the manual I downloaded from Ariens before I left lists them as ST927LE and 921005.
Dr_Woof


Don't blow into the wind, and don't eat yellow snow. WOOF!

Location: Saskatchewan
Joined: Dec 13, 2010
Points: 253

Re: No grease zerks on Ariens 926le auger shaft
Reply #5   Feb 23, 2012 10:41 pm
RedOctobyr wrote:
Just in terms of what people do, I personally don't pull the machine apart at the end of the year. My MTD did not have grease zerks. I hopefully put some grease on the shafts when I last had them apart ~9 years ago, but I couldn't say for certain. They haven't been removed since They are also still free on the shaft. They can move around a little bit on the shaft, which may help. If they had a nice snug fit, and did not wiggle on the shaft, I'd expect they'd rust solid much more easily and sooner. I do store it indoors, so its out of the weather.

If you can add zerks easily, it certainly wouldn't hurt. Worst case, at the end of the season, you could try to spray/drip some oil into the shafts, from the ends, then remove the shear pins and spin the augers on the shafts? That would both help to distribute the oil, and also maybe knock down the rust that was forming.

Rather than oil which could wash out, why not try some of the antirust type products that foam up and displace water?

Replies: 2 - 5 of 5Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42