Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Is there any brilliant minds that can make a metal craftsman snowblower chute

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
BillG


WE WILL GET IT MONDAY

Joined: Nov 12, 2005
Points: 4

Is there any brilliant minds that can make a metal craftsman snowblower chute
Original Message   Sep 5, 2008 1:20 pm
This is my 4th plastic chute for my craftsman snowblower.  It is about 6 years old.  If a person  out there can make a metal chute for this snowblower,  he could become rich. If anyone has any ideas let me know  I have a 9 HP Craftsman snowblower.  Model # 536.887992   Thank You

WE WILL GET IT MONDAY
Replies: 20 - 22 of 22Next page of topicsPreviousAllView as Outline
Oneplay


Joined: Oct 11, 2010
Points: 11

Re: Is there any brilliant minds that can make a metal craftsman snowblower chute
Reply #20   Jan 20, 2011 5:03 am
I also had a craftsman with a plastic chute for 10+ years before giving it to my brother  recently with the chute still in near perfect condition.

Perhaps its the larger engine and accompanying force of the discharged snow in your machine as mine was only a 5 hp unit but the polymer chute worked perfectly well for me.
dmottv


Joined: Jan 19, 2011
Points: 2

Re: Is there any brilliant minds that can make a metal craftsman snowblower chute
Reply #21   Jan 26, 2011 9:57 am
To follow up: I picked up a thin metal tie at Home Depot, drilled out holes to line up with my "frankenstein" reinforcement bolts as described in my earlier post, bolted it to the one side that ripped out, and it is working for now. The metal tie reinforces the plastic chute, bolted at the bottom end to one of the bolts of the chute base, and at the top end to one of my new bolts drilled through the plastic chute about 1.5" above the base. The metal tie was about 2" wide by about 12" long, predrilled with a number of small holes, I cut it in half. BTW, I installed the new hex head bolt through the chute with the head on the inside, a nylon lined lock nut on the outside, to avoid snow buildup, etc.

The bolt on the chute pivot is not working very well either, it eventually slips when blowing snow wetter than can be "broomed". I think I'll look for a couple of washers with teeth, or some other "repair" method.

I have access to a somewhat similar vintage Craftsman 5hp 24" snowblower as well, and the chute on that one is still in pretty good shape. There may be some merit to the comment above about the greater force of the larger snowblower.

This message was modified Jan 26, 2011 by dmottv
Totowasteve


Joined: Mar 26, 2018
Points: 1

Re: Is there any brilliant minds that can make a metal craftsman snowblower chute
Reply #22   Mar 26, 2018 7:16 am
I run two different blowers, both 8 HP, and have blown the top of the chute practically off on each machine, but instead of just buying a whole new chute, I put them on a piano hinge instead of the internal wire hinge that they come with. So far so good, been several storms and frozen over snow, and they are holding up great. My problems were from blowing chunks of ice.
Replies: 20 - 22 of 22Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42