Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Toro 824 snowblower won't move? ( Revised )

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
xlzleddielzlx


Location: Hartland, Wi
Joined: Dec 29, 2007
Points: 3

Toro 824 snowblower won't move? ( Revised )
Original Message   Dec 29, 2007 11:53 am
Toro 824 snowblower won't move? ... Im a first time owner of a snowblower ... I actually don't own it, a buddy from work is letting me borrow it.  Theres only one problem with it; it won't self propel.  I have no idea how these things work so when I take the bottem plate off all I see is an assembly of gears and friction disks and belts.  What would I look for in order to diagnose this problem?

Thank you in advanced

This message was modified Dec 30, 2007 by xlzleddielzlx
Replies: 2 - 6 of 6Next page of topicsPreviousAllView as Outline
xlzleddielzlx


Location: Hartland, Wi
Joined: Dec 29, 2007
Points: 3

Re: Toro 824 snowblower won't move? ( Revised )
Reply #2   Dec 30, 2007 8:46 am
I've Examined The Snowblower and I've figured out part of the problem ..... the previous owner of the snowblower had the tires on wrong.  They had them on the axle to far and didn't have the pin through the rim.  Just through the axle which in turn wasn't spinning the wheel with the drive system.  So that part is fixed.  But it appears that its still lacking some speed/power and the belt appears to be quite loose.   Can the belt tension be adjusted or is it just a matter of replacing the belt?  And if this is the case how do you go about replacing the belt?

Thank you again in advanced

niper99


Location: London Ont
Joined: Dec 2, 2007
Points: 354

Re: Toro 824 snowblower won't move? ( Revised )
Reply #3   Dec 30, 2007 6:27 pm
yes the belt can be adjusted, there should be an adjustable tensionor on the drive belt if its adjusted all the way then the belt needs to be replaced, take the old belt off and bring with u too a local repair shop a they will measure the belt and give you the correct one.   good luck!
This message was modified Dec 30, 2007 by niper99
xlzleddielzlx


Location: Hartland, Wi
Joined: Dec 29, 2007
Points: 3

Re: Toro 824 snowblower won't move? ( Revised )
Reply #4   Dec 31, 2007 10:41 pm
Thank you for the response.  How do I take the belt off if that is in fact something that has to be replaced?
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Toro 824 snowblower won't move? ( Revised )
Reply #5   Jan 1, 2008 10:51 am
For a manual Google "Toro". Select Homeowner. Under Customer Care
select Operators and Parts Manuals. Enter your model number, not 824,
the 38xxx number of a plate on the blower. They have there the
Operator's, Parts and Drive manuals for the 824. The Drive manual
is detailed on how to change and adjust the bets.
David
niper99


Location: London Ont
Joined: Dec 2, 2007
Points: 354

Re: Toro 824 snowblower won't move? ( Revised )
Reply #6   Jan 2, 2008 2:36 am
xlzleddielzlx wrote:
Thank you for the response.  How do I take the belt off if that is in fact something that has to be replaced?

well u could try to remove the crank pulley but its probally siezed on the crank, l've had to loosen the engine mounts and tilt the engine foward to remove the belt.
Replies: 2 - 6 of 6Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42