Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Carb leaking gas Toro 7/24

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
rk055


Joined: Dec 3, 2005
Points: 7

Carb leaking gas Toro 7/24
Original Message   Dec 3, 2005 3:15 pm
Hello I hope one of the experts can help me. We have a Toro snowblower 7/24 Model 38050 that we bought new back in 1981 I believe. It has been a work horse all these years and almost problem free until now. It leaks gas from the carb BUT I can stop the leak by using the shut off valve.

 I did the following: I replaced  the inlet needle - seat- clip and clip, float and also a new gasket around the bowl. Well it still LEAKS gas.

 I gave up on it for now and just wondering if anyone has any ideas. Maybe I installed the new seat in wrong? I made sure it went up all the way is that right? I cannot see anything else that would cause  this problem unless I have the wrong parts in??? I used a kit 631920 for the inlet assmb'ly.  Anytthoughts would be most helpful, I still can use it but will have to use the shutoff after I finish each time.

Ray
Replies: 7 - 16 of 16Next page of topicsPreviousAllView as Outline
rk055


Joined: Dec 3, 2005
Points: 7

Re: Carb leaking gas Toro 7/24
Reply #7   Dec 5, 2005 8:30 am
Thanks Marty, that makes alot of sense. I did put the mixture screw back to where it was and it does run normal,  just that leak problem that I use the shut off to stop.

I would think that the "seat" does not go all the way up but is the part that gets moved (up or down" to make the proper float adjustment, am I understanding you correctly? Also because this is a 25 year old machine I am concerned about breaking a bolt  to take the carb off. 

The local shop wants 40.00 Pick up & re-delivery and then he also said about 75-100 to reapair the leak. That does not count a carb if needed because of the machine age.  This is why I decided to do it myself, and I did take the bowl off about 6 years ago when sediment caused blockage, fixed it and it did not leak and work until this problem.

The other concern was that  clip. it seems to come off to easily.

Ray
snowballdgs


Joined: Nov 15, 2005
Points: 10

Re: Carb leaking gas Toro 7/24
Reply #8   Dec 5, 2005 10:08 am
Just some quick suggestions if this a tecumseh engine. First, make sure the carb is clean. The seat described here, is put in wrong. Rings must be faced down first, and smoothside is for the inlet needle.Check float even if new, for leaks, adjust  float with a 11/64 inch drill bit.Put spring on with the pointed end towards the choke, yes, it's suppose to be lose.Float bowl cutout, should be on the inside towards the engine parallel with the float post . this makes sure that the float is able to drop in the bowl far enough to allow the fuel  to enter the carb. Make sure the bowl is vented , if plugged , this will cause the carb to flood. Was there any water in the carb and froze? if so you may have a small hair line crack somewhere causing the leak. It's usually and easy fix, keep working at it you'll get it working right.I hope this helps .

                                                                                                                                                                                                             Happy fixing from, snowballdgs

rk055


Joined: Dec 3, 2005
Points: 7

Re: Carb leaking gas Toro 7/24
Reply #9   Dec 5, 2005 7:27 pm
Thanks to ALL for trying to help me with this leak problem!!!!  I gave up until it gets warmer, I did try to adjust the float with a 11/64 drill bit as explained (thank you) but must be off a little yet as it still leaks, I can use it but have to use the shut off.  I don't want to attempt to take the carb off as after 25 years I am concerned about snapping a bolt, so I have been trying to adjust with the carb on. I know not a good idea!!!  When it gets warmer and I can get some help I will try again,  BUT at least I know what is wrong!!  I checked the price on a new one a 8/26 and it goes for 999.99.......will get this one fixed!!!

Best to all and THANK YOU.

Ray
hirschallan


If it aint broke don't fix it !!


Location: Northern Hills of NY
Joined: Aug 25, 2005
Points: 327

Re: Carb leaking gas Toro 7/24
Reply #10   Dec 6, 2005 12:58 am
Ray

I find it hard to believe you'll snap the bolts.They aren't as tight as you may think. Use the proper fitting tools and you'll be amazed how easy that comes loose.

Good luck,Allan

TheKneebiter


Joined: Oct 22, 2004
Points: 233

Re: Carb leaking gas Toro 7/24
Reply #11   Dec 6, 2005 10:43 am
Marty ,

In my Tecumseh manual  it says that the ring side of the seat should be up into the carb and the smooth side is where the needle seats . Page 26  figure 29  manual 692509 ? Majorxlr8n wrote:

Ray - did you set the float level & if so, what measurement did you use? The "seat" should be installed with the smooth side going up into the carb body, and the "rings" on the other side of the seat should be visible if you look up where it sits in the seat cavity.

Marty



Majorxlr8n


Location: Freehold NJ
Joined: Aug 6, 2003
Points: 1092

Re: Carb leaking gas Toro 7/24
Reply #12   Dec 6, 2005 4:27 pm
Thanks guys - I checked my manual & the seat SHOULD be installed with the "rings" side inserted FIRST. I doubt thats the problem, as I have installed them upside down & the float still seats ok...

Marty

rk055


Joined: Dec 3, 2005
Points: 7

Re: Carb leaking gas Toro 7/24
Reply #13   Dec 6, 2005 4:46 pm
I just get concerned about snapping the bolt or bolts as it is 25 years with not being taken off.  But will give it a try when it get warmer.

I lost my original manual for this toro 7/26, Model 38050, I see that some of you have the manual? Any way if I pay for a copy would someone be kind enough to make me a copy?? It would help  so much, I have all my other ones but a few years back I think it was moved in the garage and I have been searching ever since.

Ray
rk055


Joined: Dec 3, 2005
Points: 7

Re: Carb leaking gas Toro 7/24
Reply #14   Dec 7, 2005 6:10 pm
Can any one help with a copy  of a manual for my 7/26 #38050 snowblower? IIf anyone can copy at least the carb info and pictoral if any I will pay for the copies. If anyone can I will give a PO Box they can send to.

Ray
Majorxlr8n


Location: Freehold NJ
Joined: Aug 6, 2003
Points: 1092

Re: Carb leaking gas Toro 7/24
Reply #15   Dec 7, 2005 6:24 pm
Ray - go to www.toro.com & have your model & serial numbers handy. Sometimes they're free, but if not they are cheap. I have a link for a Tecumseh manual that I will PM to you later when I get to work (I don't have it handy)

Marty

Majorxlr8n


Location: Freehold NJ
Joined: Aug 6, 2003
Points: 1092

Re: Carb leaking gas Toro 7/24
Reply #16   Dec 8, 2005 1:22 am
Ray - you have a PM with the link...

Marty

Replies: 7 - 16 of 16Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42