Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Honda HS1132 auger/blower turn independently of auger pulley

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
MarkInParis


Joined: Feb 5, 2015
Points: 1

Honda HS1132 auger/blower turn independently of auger pulley
Original Message   Feb 5, 2015 4:17 pm
I have a Honda HS1132 that ran over something that made a noise and instead of breaking the shear bolts the complete auger and blower assembly now turns independently of the auger pulley. I can not see behind the blower (blade) or in front of the auger pulley. I have been searching and researching drawings, parts and forums for some clues to the issue. I can't find anything. MY GUESS: is that there is a shaft (a 2-4" shaft) that attaches the blower to the auger pulley. There must be a bolt or pin that has broken. This is a vary difficult area to see and I would need to remove the complete auger/blower assembly and housing just to get a view. Is there anyone that has a picture, drawing or knowledge of what this looks like and what could be the problem?
Replies: 3 - 5 of 5Next page of topicsPreviousAllView as Outline
hirschallan


If it aint broke don't fix it !!


Location: Northern Hills of NY
Joined: Aug 25, 2005
Points: 327

Re: Honda HS1132 auger/blower turn independently of auger pulley
Reply #3   Feb 6, 2015 3:34 pm
Trouts, That is if it's a grade 5 bolt. One more thing worth a mention, not to tighten down any shear bolt but rather stop at the point where it can still spin some. Otherwise it takes a bit more to shear and risk something else breaking rather than the bolt. Iv'e seen bolts so tight that the tube and shaft are pressed together and that's not correct.

RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Re: Honda HS1132 auger/blower turn independently of auger pulley
Reply #4   Feb 6, 2015 7:26 pm
hirschallan, good advice, thanks. I just had to replace my first one recently, and was unsure how tight to make it. I left it a bit loose, so it could still turn.

Also, if your machine has grease fittings on the augers, use them. And maybe once a season, when you grease them, remove the shear bolts and spin the augers on the shaft. If the augers rust to the shaft, they can apparently be incredibly difficult to remove, plus the shear bolts are now useless, so you can blow an auger gearbox.
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Honda HS1132 auger/blower turn independently of auger pulley
Reply #5   Feb 7, 2015 7:25 am
   Good point on the nut.   There's a lot of vibration in there.  When I've got them I use a self locking on the drive shaft bolt.  For the rakes just a regular nut
cranked down.   A longer bolt for the drive shaft double nutted would work.
  
Replies: 3 - 5 of 5Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42