Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Honda HS621 restoration

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Honda HS621 restoration
Original Message   Oct 27, 2013 8:57 pm
Well here is my most recent find.  Actually I bought it at an auction back in August.
But didn't get around to restoring it until earlier this month.
It was pretty rough but started on the second pull. So figured it
was worth the 40.00 I paid for it.


   

The upper handle was pretty messed up.  So I replaced it with one that I kept around from and old Toro CCR2000.
It bolted right up and was also a little longer than the stock Honda handle.  Which is nice.





Stripped and repainted the muffler cover.  As well as the lower handles.


 

The blower housing sides needed quite a bit of straighting.  Also welded on a small piece of steel onto the bottom of the left  side
where it had been worn off.  Not adding the piece would have allowed snow and water to get inside what is the belt and pulley
compartment.  That would not be good.  Installed a new set of paddles and a new scraper that I bought on ebay for $53.00

 


Cleaned up everything inside.  Have to say that these blower are really well built.  The steel used for the bucket and the
undercarriage is heavy gauge.  Actually the undercarriage is plate steel.  The bracket between the engine and the bucket
is like something you would find in a automobile.

 

Sandblasted the bucket and sealed some of the joints with auto Spot putty.  Gave it two coats of Rustoleum Red oxide primer.
Then two top coats of Krylon Tough Rust semi gloss.  I did end up giving the center interior section of the housing another
coat of black Rustoleum Hammer finish.  That gave it a smoother, slicker finish and that paint if extremely durable.
That is also what I painted the auger with.

 



 

Didn't do much else other than check the carb bowl for dirt or signs of water. 
Replaced the plug, oil was good and clean.  Belt was good.  So it's ready to go.

In case some of you noticed there is a modification that I made.  I designed a chute rotator system for it.
Which I will show in another thread.


This message was modified Jan 2, 2014 by a moderator
Replies: 60 - 69 of 78Next page of topicsPreviousNextNext page of topicsAllView as Outline
NJhonda


Joined: Jan 9, 2014
Points: 25

Re: Honda HS621 restoration
Reply #60   Jan 21, 2014 8:37 am
Looks like Ill be trying out the new HS621 later today and tomorrow. Looks like 10"-12" here later today
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Honda HS621 restoration
Reply #61   Jan 21, 2014 3:44 pm
NJhonda wrote:

Actually using it for 4 years I can clearly say that the initial $50 cost has been absorbed :)

I hear what you're saying.
But that doesn't change the math.
RIT333


Joined: Jan 3, 2008
Points: 33

Re: Honda HS621 restoration
Reply #62   Jan 21, 2014 5:05 pm
jrtrebor wrote:
I hear what you're saying.
But that doesn't change the math.
I guess we can assume that he doesn't work for the IRS !
NJhonda


Joined: Jan 9, 2014
Points: 25

Re: Honda HS621 restoration
Reply #63   Jan 21, 2014 7:00 pm
I guess if you count the spark plug and gas i used in the old one too you can say i paid even more for the new one.. geeze..
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Honda HS621 restoration
Reply #64   Jan 22, 2014 9:15 am
NJhonda wrote:
I guess if you count the spark plug and gas i used in the old one too you can say i paid even more for the new one.. geeze..

No, I wouldn't say that.  Those things are considered maintenance and operating costs.
That's different.

I know it's not a big deal. I only made the comment to clarify things for
others that haven't read all the posts.
aa335


Joined: Nov 29, 2008
Points: 2434

Re: Honda HS621 restoration
Reply #65   Jan 25, 2014 2:52 am
NJhonda wrote:
I guess if you count the spark plug and gas i used in the old one too you can say i paid even more for the new one.. geeze..

Even if you were off by $100, that is still an awesome machine you got at those prices.  :)  That's why I'm not nick picking.
NJhonda


Joined: Jan 9, 2014
Points: 25

Re: Honda HS621 restoration
Reply #66   Jan 25, 2014 8:20 am
Here is my Son giving the mint 621 a workout. BTW- its all original. All the way from the spark plug and belt and paddles.

GtWtNorth


https://t.me/pump_upp

Location: https://t.me/pump_upp
Joined: Nov 16, 2008
Points: 264

Re: Honda HS621 restoration
Reply #67   Jan 25, 2014 9:38 am
I wonder if he appreciates what a great machine it is? By the way is he having so much fun that he wanted to do the sidewalk too, or are you responsible for the stretch on your property?

https://t.me/pump_upp
NJhonda


Joined: Jan 9, 2014
Points: 25

Re: Honda HS621 restoration
Reply #68   Jan 25, 2014 10:29 am
Oh he does. He took the 5 hour trip with me to get it and hes right there when I work on it. I like to do all the sidewalks and about 7-10 driveways in my neighborhood of older people to help em out
GtWtNorth


https://t.me/pump_upp

Location: https://t.me/pump_upp
Joined: Nov 16, 2008
Points: 264

Re: Honda HS621 restoration
Reply #69   Jan 26, 2014 8:49 am
Poor kid, you've passed the OPE flu to him. Soon he'll be wandering the streets on garbage day looking for a fix,  and then he'll start posting here! So sad.

Cheers
Paul

https://t.me/pump_upp
Replies: 60 - 69 of 78Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42