Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Toro 421, Gas in carb or not?

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
CharlesW


Joined: Jan 9, 2011
Points: 76

Toro 421, Gas in carb or not?
Original Message   Feb 7, 2011 11:38 am
Since I have installed a shut-off valve in the gas line of my Toro 421, I had a question about how best to use it.

If it is an ethanol problem, I shouldn't have to worry since I don't use ethanol.
If it is not ethanol related and is a manufacturing defect with the float needle, my shut-off valve should prevent the flooding of either my garage floor or the crankcase of the engine.
Bear with me.
Would it be better to run the machine after I close off the gas supply until it dies?
If I do that, the needle and seat won't be immersed in gasoline for days at a time which could be accelerating the failure of the plating on the needle.
As you have probably figured out, it's been a long winter for me and I spend too much time thinking.
This message was modified Feb 7, 2011 by CharlesW
Replies: 12 - 18 of 18Next page of topicsPreviousAllView as Outline
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Toro 421, Gas in carb or not?
Reply #12   Feb 8, 2011 8:36 am
Marc,

   Thanks for posting that picture of the 2450 shutoff install.  It just did not occur to me to do that.  Got it in yesterday.

mml4


Snow is good,
Deep snow is better!


Joined: Dec 31, 2003
Points: 544

Re: Toro 421, Gas in carb or not?
Reply #13   Feb 8, 2011 9:05 pm
trouts2 wrote:
Marc,

   Thanks for posting that picture of the 2450 shutoff install.  It just did not occur to me to do that.  Got it in yesterday.


My Pleasure-Did you put one in a 2450 or one of the newer 221or421 units?

Marc

SnapperV210P,Toro22177,TroyBilt42010Snowthrower,Craftsman Shredder,American Turbo Pressure Washer HondaGX200,Stihl011Saw,EchoPas260Trimmer Edger,EchoPB602Blower,EchoHCR150Hedge Clipper
CharlesW


Joined: Jan 9, 2011
Points: 76

Re: Toro 421, Gas in carb or not?
Reply #14   Feb 9, 2011 10:19 am
trouts2wrote:
Thanks for posting that picture of the 2450 shutoff install.  It just did not occur to me to do that.  Got it in yesterday.




mml4 wrote:
My Pleasure-Did you put one in a 2450 or one of the newer 221or421 units?

Marc


The picture referred to looks almost exactly like my installation on my 421.
Evidently the Toro SS units share some body panels.
The access actually looks like it might have been intended as a location for a shut off valve which they decided not to use.
This message was modified Feb 9, 2011 by CharlesW
Dr_Woof


Don't blow into the wind, and don't eat yellow snow. WOOF!

Location: Saskatchewan
Joined: Dec 13, 2010
Points: 253

Re: Toro 421, Gas in carb or not?
Reply #15   Feb 9, 2011 10:39 am
When and WHY did they stop putting shutoff valves on blowers?  My 30 year old JD826 has it, and so does my new Honda 928.  I consider them essential and should be mandatory.
This message was modified Feb 9, 2011 by Dr_Woof


CharlesW


Joined: Jan 9, 2011
Points: 76

Re: Toro 421, Gas in carb or not?
Reply #16   Feb 9, 2011 10:48 am
Dr_Woof wrote:
When and WHY did they stop putting shutoff valves on blowers?  My 30 year old JD826 has it, and so does my new Honda 928.  I consider them essential and should be mandatory.

I think one reason is that very few people actually use them.
I use the one on my old MTD/Dayton when storing it, but didn't use it regularly during the season, maybe 1/2 the time.

The bigger reason is probably money.
If the mfg. pays as little as a buck or two for the extra cost of installing the shut off, (And I think that would be cheap, considering the cost of parts and the added labor step), and they sell 100,000 machines, that extra $100,000 or $200,000 would almost pay some executives bonus for the year.
Dr_Woof


Don't blow into the wind, and don't eat yellow snow. WOOF!

Location: Saskatchewan
Joined: Dec 13, 2010
Points: 253

Re: Toro 421, Gas in carb or not?
Reply #17   Feb 9, 2011 10:55 am
Well...I replaced a steel shutoff valve on my daughters MTD blower and it only cost a couple bucks or so for a plastic replacement.  The steel valve was just a hunk of rust at that point (bottom of the tank - where all the water collects).  Given that a plastic valve is probably cheaper to make than a steel valve, and will not rust, I thinkc it speaks to the intelligence of some of the engineers who design these things.
This message was modified Feb 9, 2011 by Dr_Woof


trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Toro 421, Gas in carb or not?
Reply #18   Feb 9, 2011 12:21 pm
mml4 wrote:
My Pleasure-Did you put one in a 2450 or one of the newer 221or421 units?

Marc


   The filter went in a "new" never used 2002 2450 I picked up a few months ago.  That cutout was perfect.   The machine has a slight gas leak which I never noticed until I put the machine in the porch.  I called Toro Toro and found it was on the tank recall list.  I checked with the local dealer and will get a new tank installed when the weather turns. 

I'm usually working on two stages and always looking to plant a shutoff or filter.  Last year at the beginning of the season I picked up a 25 pack of the red inline Briggs filters.  I've only planted a handfull though.  There's no room on many machines. 

Replies: 12 - 18 of 18Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42