Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Electric start question

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jgreen


Joined: Sep 9, 2003
Points: 149

Electric start question
Original Message   Mar 2, 2005 12:36 pm
I removed the electric start from my 5hp snowking  because it was not engaging everytime.   I  put some oil on the  shaft  and reinstalled the starter   Now it doesnt seem to contact the flywheel at all.    Is there a trick to installing one ?      All I did was line the holes up  and put the bolts back on.  do I have to do anything else?

thanks

John
Scotts 21" self propelled  mower
MTD  4.5 HP single stage snow thrower
Snapper 3 HP single stage snow thrower
Yardman 5HP two stage snowblower
Replies: 7 - 11 of 11Next page of topicsPreviousAllView as Outline
walbroman


Clean Carb Clean Machine

Location: Plattsburg
Joined:
Points: 102

Re: Electric start question
Reply #7   Mar 7, 2005 12:05 am
Never put oil or grease on a starter shaft that's a bad thing to do. Check out brush they may be worn out or pignon gear worn out too

jgreen


Joined: Sep 9, 2003
Points: 149

Re: Electric start question
Reply #8   Mar 7, 2005 1:16 pm
walbroman wrote:
Never put oil or grease on a starter shaft that's a bad thing to do. Check out brush they may be worn out or pignon gear worn out too

That may be my problem then!       I will take if off the blower and reexamine it .       Can these starters  be repaired or  do Ineed to buy a new one.    Like I said it  was engaging some of the time when I first got the blower,   Now it seems the motor is spiining but not engaging the fly wheel on the motor.

John
Scotts 21" self propelled  mower
MTD  4.5 HP single stage snow thrower
Snapper 3 HP single stage snow thrower
Yardman 5HP two stage snowblower
spottedpony


Joined: Aug 23, 2004
Points: 301

Re: Electric start question
Reply #9   Mar 8, 2005 12:19 am
any metal to metal contact such as in a  starter is going to create excessive wear without lubrication.......thats why starter mfgrs use lubriplate or similar white grease sparingly in these applications, dont go overboard but a bit of lubrication is necessary to get long live from a starter. (assuming as asked in an earlier post, that the starter motor runs ok and the bendix is just not engaging) and if the bendix is worn out, it could be due to lack of lubrication causing excessive wear. personally i wouldnt reassemble one without a bit of lube.
walbroman


Clean Carb Clean Machine

Location: Plattsburg
Joined:
Points: 102

Re: Electric start question
Reply #10   Mar 8, 2005 1:51 am
Well some say lubricate some say's no but one thing for sure this unit becomes hot after time if it runs to long over 10 seconds is too much it could get hot if you want to put lithium grease a bit I dont see an inconvenient but all my starter here doesnt have any grease at all and I never had problem with it as long that id no water going on the shaft and pignon

Walby

Termy


Location: Washington
Joined: Oct 24, 2004
Points: 960

Re: Electric start question
Reply #11   Mar 8, 2005 3:02 am
On the oiling thing, there is only one type of oil that can go on electronic parts without any damage. WD-40

I have a Murray RER that no longer runs. When I first got it, the startor would exibit the same symptoms as yours. All, I did was clean in up with WD-40 and she never had problems again!


Replies: 7 - 11 of 11Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42