Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Putting Belt back on Ariens 824

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
mason156


Joined: Jan 28, 2005
Points: 7

Putting Belt back on Ariens 824
Original Message   Jan 28, 2005 11:51 am
The other day the attachment/Auger belt jumped off the pulley of my Ariens 824.  (Thankfully it happened after I had cleared the whole driveway).  The belt is still intact. According to the manual, I have to remove the whole front housing to replace the belt.  My questions are:

1.  Do I REALLY have to remove the housing?
2.  If I do have to remove the housing,  How bad is that? 
3.  If I do have to remove the housing, is is worth replacing both the belts while I'm in there?

Thanks in advance,.

Steve
Replies: 6 - 8 of 8Next page of topicsPreviousAllView as Outline
RalphS


There's a reason for more than one snowblower.
Because.
1974 Ariens 824 SnoThro
197? Ariens ST270 SnoThro
1988 Ariens ST824 SnoThro
196? REO Snowblower
1960 Ariens SnoThro
1964 Ariens SnoThro


Location: MA
Joined: Dec 21, 2004
Points: 70

Re: Putting Belt back on Ariens 824
Reply #6   Jan 29, 2005 7:40 am
I replaced the belt on my 1974 824 a few weeks ago.  My manual also says to separate the auger housing from the drive housing.  I tried to feed the new belt around the pulleys for about 15 minutes, then gave up.  

It took less than 15 minutes to separate the housings, put on the new belt, check everything over, and re-attach housings ( I had to remove the chute angle adjuster, too).  The new belt rubbed on the wire metal "guides" that I suppose are to keep the belt from bouncing.  I had to adust them slightly.  I don't think I would have seen that if the halves were together. 

It was also easier adjusting the idler pulley. 

My two cents. 

Good luck. 

RalphS


There's a reason for more than one snowblower.
Because.
1974 Ariens 824 SnoThro
197? Ariens ST270 SnoThro
1988 Ariens ST824 SnoThro
196? REO Snowblower
1960 Ariens SnoThro
1964 Ariens SnoThro


Location: MA
Joined: Dec 21, 2004
Points: 70

Re: Putting Belt back on Ariens 824
Reply #7   Jan 29, 2005 8:00 am
Sorry for the additional post, but I didn't answer all your questions.  I'm familier with my 824 with one belt, but things should be similar. 

Separating the two halves is easy.  It helps to have another person, but not at all necessary.  I first removed the chute adjuster from the chute by removing the one nut (at the chute end), then setting the rod assembly out of the way.  You may remove it in a different manner, just look at what would be easiest. 

You also might have to remove something that adjusts the auger drive belt, I'm not sure. 

Find something reasonably solid like a milk crate and place it behind the unit (under the handlebar area). 

There are two bolts on either side of the unit near the top of the auger assy where it meets the drive section.  Remove them, but be careful, when they are removed, the two halves can now pivot apart, hinged on a rod at the bottom of the unit (this is where the second person is helpful).  The auger assy has a kind of notch that hooks onto this rod.  This is where the milk crate under the handlebars comes in handy- to prevent the drive assy from tipping backwards. 

Once separated, everything should be visible.  Try and figure out why the belt fell off.  Might be stretched.  I would replace both belts while you're in there. The belts are not too expensive.  Keep the old ones as emergency spares.  I haven't replace the belts on my two-belt 824 yet, but re-attaching the auger belt may be a little trickier than the one-belt system when re-attaching the halves.

Good Luck

Ralph 

 

mason156


Joined: Jan 28, 2005
Points: 7

Re: Putting Belt back on Ariens 824
Reply #8   Jan 31, 2005 8:12 pm
I finally got the chance to address my problem today and found that both approaches (taking the housing off and not taking the housing off) were right.

I first removed the belt cover and bottom plate, drained the fuel, and tipped the machine onto the Auger housing.  Sure enough, it was easy to put the belt back on the pulleys and get myself back in business.  After I put the belt on, I tipped the unit back, added some fuel and started it up to check for problems.

 The Auger pulley was shimmying and the belt was dancing around.  Closer inspection revealed that the cast hub that attached the pulley to the shaft was cracked.  I followed the instructions in the manual and split the housing from the engine assembly (using the tailgate of  my pickup instead of a milk crate).  It wasn't a bad job at all.  Turns out my local dealer has the part in stock, so I should be back in action tomorrow.  (I will swap the belts as well.)

Thanks to all for your advice.  It made the job very easy and worry-free.

Steve
Replies: 6 - 8 of 8Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42